Statistics and Operating Charts

One of the important advantages of DSVT is the ability to monitor heating, cooling, and domestic hot water production in detail using Domoticz logging and graphical visualisation features.

By default, Domoticz supports recording and graphically displaying measurement data and state changes from many sensors and switching devices.

In addition to conventional device-specific charts, DSVT provides its own consolidated graphical overview, designed to display the most important system operating events in a single, easy-to-understand interface.

These consolidated charts are particularly useful for analysing control processes, verifying switching between heat sources, and fine-tuning energy-efficient operation.

1. Opening the DSVT Statistics Interface

The DSVT statistics and graphical interface can be accessed through the Domoticz Custom menu.

The corresponding menu item is:

Custom → DSVT_HMV_ZONE_12

The interface can be accessed directly at:

/#/Custom/DSVT_HMV_ZONE_12

The graphical display presents the system's relevant measurements and switching events on a shared time axis.

This makes it easier to identify relationships between events that would be more difficult to recognise when viewing separate charts for individual Domoticz devices.

2. Overview of the Last 24 Hours

DSVT's consolidated charts allow users to examine important operating events from the previous 24 hours.

Different sensor measurements, control values, and switching events can be displayed along a common time axis.

For example, this makes it possible to examine:

The 24-hour display also allows daytime and nighttime operating periods to be compared.

3. Heating and Cooling System Chart

The heating and cooling chart provides a combined overview of the most important variables and switching events affecting system operation.

It helps users understand how DSVT responds to changing temperature demands and environmental conditions.

Temperature Measurements

Based on the measurement data available in the system, temperature changes relevant to heating and cooling control can be monitored.

These measurements help explain the conditions under which the controller activated or deactivated equipment.

Heat Source Operation

In installations with two heat sources, comparing their activation and deactivation events is particularly useful.

For example, the chart can help verify:

This is especially important when a heat pump and gas boiler are used together, as heat source selection can have a significant effect on energy efficiency.

Switching Frequency

Unusually frequent activation and deactivation can be identified by examining switching events on the chart.

Excessive switching may be caused by inappropriate hysteresis settings, sensor measurement errors, or unsuitable control parameters.

Analysing switching events alongside temperature changes can make it easier to identify the underlying cause.

4. Domestic Hot Water Production Chart

DSVT provides a separate graphical overview for analysing processes associated with domestic hot water (DHW) production.

The DHW chart allows users to monitor measurements and switching events related to tank heating.

Depending on the installed equipment and configuration, the following can be examined:

The chart can help verify whether the tank is heated according to the configured control conditions.

Analysing DHW Heating Cycles

Comparing tank temperature measurements with switching events makes it possible to examine how DHW heating cycles develop.

This can help identify:

When evaluating these conditions, domestic hot water consumption, tank heat losses, and the actual system configuration must also be considered.

5. Overview of the DSVT Graphical Interface

The following image shows an example of DSVT's consolidated statistical display.

The shared graphical interface allows different measurements and switching events to be compared over time.

DSVT consolidated heating and cooling system statistics chart

When interpreting the chart, comparing heat source switching times with temperature changes can be particularly useful.

6. Identifying Control Problems

The consolidated charts are useful not only for monitoring operation but also for identifying control problems.

Examining relationships between events over time makes it easier to recognise undesirable operating behaviour.

Frequent Switching

If a heat source repeatedly switches on and off at short intervals, the hysteresis and switching delay settings should be examined.

Slow Temperature Response

If room temperature responds to control interventions only after a significant delay, this may be caused by the high thermal inertia of the heating system or building.

The configured update and calculation intervals may also influence control response times.

Incorrect Heat Source Switching

When two heat sources are used, switching events can help verify whether DSVT changes between them according to the selected control conditions.

DHW Control Irregularities

Comparing the DHW tank temperature curve with heating switching events can help identify irregularities associated with the target temperature or hysteresis settings.

Important: a chart alone does not prove the cause of a problem, but it can significantly simplify troubleshooting.

7. Analysing Energy Efficiency

DSVT charts can provide valuable information for evaluating the energy-efficient operation of heating and cooling systems.

By analysing heat source operating periods and switching events, users can observe how system behaviour changes under different environmental and control conditions.

Particularly useful analyses include:

The charts can help determine how configuration changes influence system operation.

Important: operating time and switching events alone do not provide accurate energy consumption measurements. Actual electricity or gas consumption must be measured using suitable energy meters.

8. Individual Domoticz Device Charts

In addition to DSVT's consolidated charts, the standard Domoticz statistics and graphical displays for individual devices remain available.

These are especially useful when examining the operation of a particular sensor or switch in greater detail.

For example:

The two graphical approaches complement each other.

The consolidated DSVT charts provide an overview of the entire system, while individual Domoticz charts allow more detailed examination of specific devices.

9. Using Charts for Fine-Tuning

When adjusting DSVT control parameters, it is recommended to monitor the effects of the changes using the charts.

This is particularly important for settings such as:

It is advisable to change only one control parameter at a time and allow sufficient time to observe the result.

In buildings with high thermal inertia or underfloor heating systems, the effects of changes may only become clear after several hours.

Observing these changes on the charts can provide a more objective basis for further fine-tuning.

10. Summary

The DSVT statistics interface complements conventional Domoticz device charts with a consolidated 24-hour operating overview.

The heating and cooling chart allows users to monitor heat source switching events, operating periods, and temperature changes relevant to control behaviour.

The DHW chart supports analysis of domestic hot water production processes and associated switching events.

Using these charts together simplifies troubleshooting, fine-tuning control parameters, and optimising system operation over time.

DSVT's consolidated statistics charts provide a clearer understanding of heating, cooling, and domestic hot water system operation and offer valuable support for reliable, energy-efficient management.

DSVT – Documentation and Guides

Browse installation instructions, configuration steps and detailed explanations of the control functions.

Heating, Cooling, DHW and Buffer Control – Overview

Overview and principles

Operational logic and operating modes

Intelligent control algorithms

Actuating devices and auxiliary controls

Installation and configuration

Usage and documentation

Version history